The poor maintenance and usage of the equipment and machines of a vegetable oil manufacturing company adversely affect its competitive advantage. These industries are faced with numerous equipment maintenance challenges in the path to increasing their throughput as well as profitability. To address the said maintenance challenges, process data were obtained for the Overall Equipment Effectiveness (OEE) factors after their Total Productive Maintenance (TPM) implementation in the company. Minitab 21 software was used to analyze the data collected, and the results showed that the mean for quality, availability, and performance obtained were 96.929%, 63.35%, and 61.20%, respectively. This shows that the quality of products is the greatest OEE factor that vegetable oil manufacturing companies must consider meticulously to reduce the six big losses in their production processes. Response Surface Method (RSM) with Central Composite design, with the application of Design Expert 13 software, was used to model, analyze, and optimize the Overall Equipment Effectiveness (OEE) using availability, quality, and performance as the input parameters. The analysis of both the actual and coded values, which is the main contribution of the study, showed that quality has the greatest value followed by availability and performance. It was found that, to effectively reduce the six big losses, the quality, performance, and availability should be targeted as 98.3052%, 81.6022%, and 80.103%, respectively.

In the current paper, the authors are intended to manufacture the aluminum based metal matrix composite (MMC) employing the stir casting process. Further, the fabricated composite sample is investigated for machining characteristics during the die sink electrical discharge machining process (EDM). EDM is most commonly employed to satisfy the special needs of industry such as developing deep holes and complex contours from high strength materials such as composites, alloys, smart materials, and functionally graded materials. In the current study A356 and 4%, tungsten carbide (WC) powder are considered as matrix and strengthening materials respectively to fabricate the MMCs. During the machining activity, the input factors like discharge current (Ip), Voltage (Vg), Pulse On-Time (Ton), and flushing pressure (P) are optimized for achieving optimum surface roughness (SR), Tool Wear Rate (TWR) and Material Removal Rate (MRR). To estimate the ideal set of process factors grey regression analysis (GRA) is used. From the results, it was observed that the GRA is found to perform better than the RSM.

Demand for eco-friendly materials increases each year due to their excellent properties, which has proved to contribute to developing a sustainable environment. One of the promising raw materials in producing Glass is rice husk, a waste product from paddy harvesting, containing about 90% of silica. Rice husks are usually burnt in an open area and contribute to severe air pollution problems. In this research, Soda-Lime-Silica Rice Husk Ash (SLRHA) glass which is a new combination of soda-lime silicate (SLS) glass and rice husk ash (RHA), was developed for building glass and window application. The hardness properties of the developed SLS-RHA glass system are presented in this paper. These glasses were investigated to determine the effect of RHA addition on the physical properties of SLS glass. The experimental works using RSM have successfully identified the significant factors and optimized the responses. Based on the Rockwell hardness test, the outcomes demonstrated that the glass sample contained 29.84% weight SLS and 0.06% weight RHA. The result indicated that crack propagation was increased with the increasing addition of RHA, which causes an increase in cracks and voids due to the creation of more debonding.

Designing a production process normally is involved with some important constraints such as uncertainty, trade-off between production costs and quality, customer’s expectations and production tolerances. In this paper, a novel multi-objective robust optimization model is introduced to investigate the best levels of design variables. The primary objective is to minimize the production cost while increasing robustness and performance. The response surface methodology is utilized as a common approximation model to fit the relationship between responses and design variables in the worst-case scenario of uncertainties. The target mean ratio α is applied to ensure the quality of the process by providing the robustness for all types of quality characteristics and with a trade-off between variability and deviance from the ideal point. The Lp metric method is used to integrate all objectives in one overall function. In order to estimate target value of the quality loss by considering production tolerances, the process capability ratio (Cpm) is applied. At the end, a numerical chemical mixture problem is served to show the applicability of the proposed method.

Inconel 718 is among difficult to machine materials because of its abrasiveness and high strength even at high temperature. This alloy is mainly used in aircraft and aerospace industries. Therefore, it is very important to reveal and evaluate cutting tools behavior during machining of this kind of alloy. The experimental study presented in this research work has been carried out in order to elucidate surface roughness and productivity mathematical models during turning of Inconel 718 superalloy (35 HRC) with SiC Whisker ceramic tool at various cutting parameters (depth of cut, feed rate, cutting speed and radius nose). A small central composite design (SCCD) including 16 basics runs replicated three times (48 runs), was adopted and graphically evaluated using Fraction of design space (FDS) graph, completed by a statistical analysis of variance (ANOVA). Mathematical models for surface roughness and productivity were developed and normality was improved using the Box-Cox transformation. Results show that surface roughness criterion Ra was mainly influenced by cutting speed, radius nose and feed rate, and that the depth of cut had major effect on productivity. Finally, ranges of optimized cutting conditions were proposed for serial industrial production. Industrial benefit was illustrated in terms of high surface quality accompanied with high productivity. Indeed, results show that the use of optimal cutting condition had an industrial benefit to 46.9 % as an improvement in surface quality Ra and 160.54 % in productivity MRR.

Inconel 825 is high nickel-chromium-based superalloy which retains its mechanical properties and exhibits good corrosion and oxidation resistance at elevated temperature. Inconel 825 is extensively used for making aircraft engine parts like combustor casing and turbine blades in aero space industry. This research proposed the Response Surface Methodology with GRA to optimize multiple responses during Wire-cut EDM of Inconel 825. At optimum combination of input parameters i.e. A4B1C1D5E4F2, increase in MRR from 36.13 mm2/min to 41.822 mm2/min, decrease in SR from 2.842μm to 2.445μm and decrease in WWR from 0.01832 to 0.01758 was obtained. Experimental results showed that pulse-on time, wire feed, pulse-off time, and peak current significantly affected the MRR, and surface integrity of specimen and electrode with the formation of craters, pockmarks, debris, micro cracks, and recast layer. The optimal parametric combination obtained from the present study will be advantageous for working on high strength; high thermal conductivity and low melting point materials like nickel alloys.

Abrasive Water Jet Machining is one of the novel nontraditional cutting processes found diverse applications in machining different kinds of difficult-to-machine materials. Process parameters play an important role in finding the economics of machining process at good quality. This research focused on the predictive models for explaining the functional relationship between input and output parameters of AWJ machining process. No single set of parametric combination of machining variables can suggest the better responses concurrently, due to its conflicting nature. Hence, an approach of Multi-objective has been attempted for the best combination of process parameters by modelling AWJM process using of ANN. It served a set of optimal process parameters to AWJ machining process, which shows a development with an enhanced productivity. Wide set of trail experiments have been considered with a broader range of machining parameters for modelling and, then, for validating. The model is capable of predicting optimized responses.

Laser direct structuring (LDS) is very important step in the MID process and it is a complex process due to different parameters, which influence on this process and its final product. Therefore, it is very important to use a reliable model to predict, analyze and control the performance of the (LDS) process and the quality of the final product. In this work we develop mathematical models by using Artificial Neural Network (ANN) and Response Surface Methodology (RSM) to study this process. The proposed models are used to study the effect of the LDS parameters on the groove dimensions (width and depth), lap dimensions (groove lap width and height) and finally the heat effective zone (interaction width), which are important to determine the line width/space in the MID products and the metallization profile after the metallization step. We also study the relationship between the LDS parameters and the surface roughness which is very important factor for the adhesion strength of MID structures. Moreover these models capable of finding a set of optimum LDS parameters that provide the required micro-channel dimensions with the best or the suitable surface roughness. A set of experimental tests are carried out to validate the developed ANN and the RSM models. It has been found that the predicted values for the proposal ANN and RSM models were closer to the experimental values, and the overall average absolute percentage errors were 4.02 % and 6.52%, respectively. Finally, it has been found that, the developed ANN model could be used to predict the response of the LDS process more accurately than RSM model.

This paper demonstrates an experimental scrutiny into turning process of hot work tool steel AISI H21 under dry machining plight. In this paper, face centered central composite design concealed by response surface methodology is practiced and analysis of variance is implemented to analyze the eloquent benefaction of machining parameters on responses. To access accommodate between the surface roughness and the MRR, an approach for concurrent optimization of multi-objective characteristics based on comprehensive desirability function is employed. The multi objective optimization concludes a spindle speed of 1599.568 rpm, feed rate of 0.262 mm/rev and depth of cut of 2 mm.

This paper presents an experimental investigation on cutting temperature during hard turning of EN 24 steel (50 HRC) using TiN coated carbide insert under dry environment. The prediction model is developed using response surface methodology and optimization of process parameter is performed by desirability approach. A stiff rise in cutting temperature is noticed when feed and cutting speed are elevated. The effect of depth of cut on cutting temperature is not that much significant compared with cutting speed and feed as observed from main effects plot. The response surface second order model presented high correlation coefficient (R2 = 0.992) explaining 99.2 % of the variability in the cutting temperature which indicates the goodness of fit for the model to the actual data and high statistical significance of the model. The experimental and predicted values are very close to each other. The calculated error for cutting temperature lies between 1.88-3.19 % during confirmation trial. Therefore, the developed second order model correlates the relationship of the cutting temperature with the process parameters with good degree of approximation. The optimal combination for process parameter is depth of cut at 0.2mm, feed of 0.1597 mm/rev and cutting speed of 70m/min. Based on these combination, the value of cutting temperature is 302.950C whose desirability is one.